Whether you’re brand new to vaping or making the switch from disposables to a refillable setup, getting the hang of vape tanks can take some time. These essential components of your device are responsible for holding your e-liquid, delivering flavor, and producing vapor, but only if they’re used properly.
Unfortunately, new vapers often run into the same issues again and again. If you’ve experienced burnt hits, leaky tanks, or underwhelming clouds, there’s a good chance you’re making one of these common mistakes. The good news? They’re all easy to fix.
Not Priming the Coil
One of the most common reasons new vapers experience burnt hits is because they don’t prime their coil before using it. Priming is the simple process of soaking the coil’s cotton wick with vape juice before you start vaping. If you skip this step, the dry cotton will burn when you fire the device, resulting in a terrible taste and a ruined coil.
How to Avoid It:
Whenever you install a new coil:
- Add a few drops of e-liquid directly onto the exposed cotton.
- Fill your tank and let it sit for 5–10 minutes.
- Take a few “primer puffs” without firing the device to draw juice into the coil.
This ensures your wick is fully saturated and ready to deliver clean, flavorful vapor.
Overtightening the Tank
It’s natural to want to keep your tank secure, especially if you’ve had issues with leaking. But overtightening your tank, whether it’s when attaching the coil or screwing the tank onto your mod, can do more harm than good. Overtightening can damage the threads, strip seals, and make your tank nearly impossible to disassemble later. It can also crush O-rings, leading to leaks.
How to Avoid It:
Tighten the coil and tank components just enough to feel resistance. Hand-tight is sufficient. If you’re straining your wrist to twist it on, it’s too tight.
Filling the Tank Improperly
Improper refilling is a common issue, especially with top-fill tanks. Accidentally pouring vape juice into the central airflow chimney will flood your coil and cause leaking and gurgling. Overfilling can also create pressure problems that lead to leaking.
How to Avoid It:
- Locate the designated fill ports, usually marked or set to the side.
- Avoid the central airflow tube.
- Don’t fill to the absolute top—leave a little room for air to help prevent flooding.
Always double-check the manufacturer’s instructions if you’re unsure about your tank’s design.
Vaping at the Wrong Wattage
Each coil has a recommended wattage range. New users sometimes ignore this and vape too hot (causing burnt hits) or too low (resulting in weak vapor and flooding). Either mistake can shorten coil life and worsen the experience.
How to Avoid It:
Check the side of the coil for the printed wattage range (e.g., 30–40W). Start at the lower end and gradually increase until you find your sweet spot. This method preserves coil life and ensures better vapor production.
If you’re using a regulated mod, it will usually allow you to dial in the exact wattage for precision control.
Neglecting Regular Cleaning
Many vapers overlook cleaning, which can lead to residue buildup, muted flavor, and even cross-contamination between different juices. If you’re switching flavors or using your tank daily, cleaning should be part of your routine.
How to Avoid It:
Once a week (or whenever you change flavors), disassemble your tank and rinse all parts with warm water. Let them air dry completely before reassembling. For a deeper clean, use a bit of dish soap or soak the parts in vodka (just don’t soak the coil head itself).
A clean tank ensures fresh flavor and helps your coils last longer.
Vape tanks can be a bit intimidating at first, but once you learn how to use and care for them properly, they become one of the most customizable and satisfying parts of vaping. By avoiding these common beginner mistakes, like not priming coils, overtightening, overfilling, or ignoring wattage recommendations, you’ll enjoy better flavor, smoother clouds, and fewer headaches.
For more information about salt nic vape and ejuice Please Visit : The Vape Mall
